Air-ConditionersINDOOR UNITPEFY-P06,P08,P12,P15,P18,P24 NMSU-EGBINSTALLATION MANUALFor safe and correct use, please read this installation manual thor
10GBDFEINLPGRRUTRCZSVHGPO9. Electrical wiringPrecautions on electrical wiring Warning:Electrical work should be done by qualified electrical engineers
11GBDFEINLPGRRUTRCZSVHGPO Caution:Install wiring so that it is not tight and under tension. Wiring under tensionmay break, or overheat and burn.9.3. C
12GBDFEINLPGRRUTRCZSVHGPO[Fig. 9.5.1] (P.5)<Address board>A SWA B SWCC SW1 D SW11E SW12 F SW149.6. Setting addresses(Be sure to operate with the
13GBEINLPGRRUTRCZSVHGPOFTable des matières1. Consignes de sécurité1.1. Avant l’installation de l’appareil et l’ins-tallation électriques Avant d’insta
14GBEINLPGRRUTRCZSVHGPODF• Demandez conseil à votre revendeur avant de mettre le produit aux rebuts.• N’utilisez pas d’additif de détection des fuites
15GBEINLPGRRUTRCZSVHGPOF4. Fixation des boulons de suspension4.1 Fixation des boulons de suspension[Fig. 4.1.1] (P.2)A Centre de gravité(Fournir une s
16GBEINLPGRRUTRCZSVHGPODF6.1. Spécifications techniques des tuyaux de réfrigérant et d’écoulement* Lorsque les modèles P18 sont utilisés avec du réfri
17GBEINLPGRRUTRCZSVHGPOFPrécautions concernant le raccordement des tuyauxde réfrigérantsssss Toujours utiliser des soudures non oxydantes afin qu’aucu
18GBEINLPGRRUTRCZSVHGPODF9. Câblage électriquePrécautions à prendre lors du câblage électrique Avertissement:Les travaux électriques doivent être mené
19GBEINLPGRRUTRCZSVHGPOF2. Câbles de la commande à distance9.1. Câblage de l’alimentation électrique• Les câbles d’alimentation électrique des apparei
33.2[Fig. 3.2.1]44.1[Fig. 4.1.1]A Refrigerant pipe (liquid pipe): HPB Refrigerant pipe (gas pipe): LPC Drain pipe (O.D. ø32 mm [1-1/4 in])D Drain pipe
20GBEINLPGRRUTRCZSVHGPODF5. Lorsque le câblage est terminé, vérifier qu’il n’y ait pas de jeu dans les con-nexions et fixer le couvercle au boîtier de
GBEFINLEPGRRUTRblank 08.1.16, 2:45 PM2
GBEFINLEPGRRUTRblank 07.11.28, 4:55 PM2
GBEFNLEPGRRUTRblank 07.11.28, 4:55 PM3
KB79K383H01HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPANPlease be sure to put the contact address/telephone number on
3A Cut hereB Remove brazed capAAECFBDA Thermal insulationB Pull out insulationC Wrap with damp clothD Return to original positionE Ensure that there i
4A Air inletB Air outletC Access doorD Ceiling surfaceE Canvas ductF Air filterG Inlet grilleABDECCCCCCC8[Fig. 8.0.1]99.1[Fig. 9.1.1] [Fig. 9.2.1][Fig
5E Use conduit to keep the weight of the cable and external force from being appliedto the power supply terminal connector.F Power source wiringG Cond
6GBDFEINLPGRRUTRCZSVHGPOContents1. Safety precautions1.1. Before installation and electric works Before installing the unit, make sure you read all th
7GBDFEINLPGRRUTRCZSVHGPO• Use ester oil, ether oil or alkylbenzene (small amount) as the refrigeratoroil to coat flares and flange connections.- The r
8GBDFEINLPGRRUTRCZSVHGPO4. Fixing hanging bolts4.1 Fixing hanging bolts[Fig. 4.1.1] (P.2)A Center of gravity(Give site of suspension strong structure.
9GBDFEINLPGRRUTRCZSVHGPO• Store the piping to be used during installation indoors and keep bothends of the piping sealed until just before brazing.- I
Commentaires sur ces manuels